ITEAD Intelligent Switch User Manual

 

W series operation description

W series switch is with remote control function, without networking function.
(Important notes: As for multi-digit button switch, if one of the buttons fails to connect with corresponding load or the load is broken, then this button, which may have power shortage, will cause system failures under light on mode when turning on the light.)

Button Indicator 
White means on, blue means off.

Remote control code learning
Pressing touch button that is for learning for around 3 seconds, then stop pressing when hearing a sound. At this moment, the switch has entered into remote control code learning status, press button on the remote control. If learning is successful, its load of the learning touch button will change status.
After learning successfully, this remote control button can control this button.

Scene on learning
Pressing touch button that is for learning for around 3 seconds, do not stop when hearing a sound and continues to press, stop pressing when hearing the second sound. At this moment, the switch has entered into scene on learning status, press button on the remote control. If learning is successful, its load of the learning touch button will change status.
After learning successfully, this remote control button will be this channel’s scene on control. To put it another way, no matter the lamp of this channel is on or off, press this remote control button, the lamp will set the status as power on.

Scene off learning
Pressing touch button that is for learning, stop pressing when hearing the third sound. At this moment, the switch has entered into scene off learning status, press button on the remote control. If learning is successful, its load of the learning touch button will change status.
After learning successfully, this remote control button will be this channel’s scene off control. To put it another way, no matter the lamp of this channel is on or off, press this remote control button, the lamp will set the status as power off.
(After you have entered the above learning status and want to quit, touch any button on the switch panel to exit learning status. If the learning is not successful within 2 minutes, the system will exit learning status automatically.)

Clean remote control code
Press any touch button and do not stop until you hear the sixth sound. At this moment, every channel’s remote control code and scene on code and scene off code will be cleaned.
(Attention: If you have heard the ninth sound after pressing the button, and you did not stop, the switch will start over automatically.)

N series operation description

N series switch is with remote control function and networking function.

Remote control code learning: the same as W series
Scene on learning: the same as W series
Scene off learning: the same as W series
Clean remote control code: the same as W series

Button Type
N series switch button has two types of buttons. They are local channel button and networking button. Every local channel button corresponds to a local load, networking button has no local load but indicator, it’s used for connecting other local channel button with networking.

Every local channel button from N series switch has the only one ID key and can be accepted by other networking button of different switch. After networking buttons joined, it can achieve actual status linkage and mutual control. For example, if you want to control living room in main bedroom and second bedroom, then you can connect both networking button in main bedroom and second bedroom with local channel button in living room. 

How does it get into network status?
Keep pressing the button that to enter network status, do not release until you hear the fourth sound. At this moment, the switch has entered into network status. Don’t touch any button on the switch before the network finishes, otherwise the system will exit network status and enter into normal working mode.

How does networking button join local channel button’s network?
Firstly, make local channel button into network status, and then make networking button into network status (pay attention to the sequence: local channel button comes first, then net work button). You will hear sounds of tick after 1-2 seconds, if it ticks three times, it means the network is successful, otherwise please operate it again. If you need to add other network buttons to this local button’s network, please do it by repeating the operation. (According to sequence to operate local channel button and other network buttons to enter into network status again)
(If you want to discontinue network after entering into network learning status, please touch any button on the switch panel in order to exit network status. If the network is not successful within 2 minutes, the system will automatically exit network learning status.)

How does the network button exit from local button network and cancel the connection?

press the network button that needs to exit from network. Do not stop until you hear the fifth sound of tick. This button will exit from ready network. (This operation is only to exit this button from network, but not other buttons. And it will also not clean the learnt remote control code)

Download:

ITEAD_Intelligent_Switch_Manual.pdf

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>